亚洲精品蜜桃久久久久久,一区二区三区四区日韩视频在线观看,亚洲综合国产精品久久久,亚洲国产欧美精品视频

銷售咨詢熱線
15953126901
18615254757
公司新聞 hengye
企業案例 case

聯系我們

  • 聯系人:濟南燕翔鐵藝制品有限公司
  • 手機:15953126901
  • 電話:18615254757
  • 郵箱:785385551@qq.com
  • 地址:濟南市天橋區歷山北路黃臺不銹鋼市場3區317
當前位置: 首頁 > 新聞資訊>公司新聞鐵藝大門的焊接工藝

鐵藝大門的焊接工藝

來源:http://www.c6271.cn 日期:2024-06-06 發布人: 瀏覽次數:1

1.邊框焊接  按邊框尺寸在地上定位。將邊框料的兩端寬邊上切成45。對接后點焊。校正無誤<方框的對角線要相等)后焊牢。

1. The border welding is positioned on the ground according to the border size. Cut the two wide edges of the border material into 45 pieces. Spot welding after docking. After correction, ensure that the diagonals of the boxes are equal and weld them firmly.

2.中間長豎管焊接  每扇門3根長豎管,均勻分布在邊框內,定位間距為339毫米。擺放好位置后,先點焊,再校平,檢查無誤后再焊牢。

2. Weld 3 long vertical pipes in the middle of each door, evenly distributed within the frame, with a positioning spacing of 339 millimeters. After placing the position, spot weld first, then level and check for accuracy before welding firmly.

3.矛頭用橫管焊接每扇門4根,夾在中問長豎竹之間、擺放好位置后,先點焊,再校平,檢查無誤后再焊牢:

3. Weld 4 horizontal pipes to each door with the spearhead, clamp them between the long vertical bamboo in the middle, place them in the right position, spot weld first, then level and check for accuracy before welding firmly:

20231024065223409.jpg

4.中間短豎管焊接  侮扇門4根.按圖樣中的位置擺好。先點焊,再校平,檢查無誤后再焊牢。

4. Weld 4 short vertical pipes in the middle and place them according to the positions in the drawing. First spot weld, then level, check for accuracy, and then weld firmly.

5.短橫管焊接每扇門24根.按圖樣中的位置擺好。先點焊,再校平,檢查無誤后再焊牢。為防l上焊接變形,可問隔焊。由于順序打亂,焊點較多,焊完后應檢查有無漏焊部位。

5. Weld 24 pieces of the shortest horizontal pipe for each door. Arrange them according to the position in the drawing. First spot weld, then level, check for accuracy, and then weld firmly. To prevent welding deformation, it is possible to ask for insulation welding. Due to the disorder of the order and the presence of many welding points, it is necessary to check for any missing areas after welding.

6.槍頭焊接依次將各槍頭分別焊在相應的位置上.要求與橫桿垂直,正面朝前,不能扭曲。

6. Weld each gun head in the corresponding position in sequence. It is required to be perpendicular to the horizontal bar, facing forward, and not twisted.

7.花形焊接把所有花形分別擺放在相應位置上,看是否合適,調整無誤后,先點焊到框架上,整體再檢查一遍,然后焊牢。

7. Flower welding: Place all flower shapes in their respective positions, check if they are suitable, adjust them correctly, first spot weld them to the frame, check the whole again, and then weld them firmly.

永德县| 宣汉县| 东乌| 二连浩特市| 江华| 广东省| 洪泽县| 双鸭山市| 鹿邑县| 六安市| 酒泉市| 汉川市| 洪雅县| 丰城市| 循化| 疏附县| 布尔津县| 漳州市| 玉溪市| 平潭县| 通渭县| 鄂托克前旗| 合川市| 高平市| 达州市| 荣成市| 温宿县| 边坝县| 昭觉县| 广灵县| 嘉兴市| 京山县| 汽车| 宁远县| 本溪市| 梁河县| 鹿泉市| 双牌县| 汾阳市| 高台县| 囊谦县|